Jump to content

Squid

VT Member
  • Content Count

    339
  • Joined

  • Last visited

  • Days Won

    14

Reputation Activity

  1. Like
    Squid got a reaction from Christopher in Contest Ideas?   
    If you just want Quick and dirty to get the stuff gone, I can PM you my address...  🤣
  2. Like
    Squid got a reaction from Tam in Smok V8   
    It's possible that the drop broke the coil in the atomizer or possibly something internal in the battery when you dropped it. As Tam said first thing to do is change the atomizer.
  3. Like
    Squid got a reaction from MRSpivey in Smok V8   
    It's possible that the drop broke the coil in the atomizer or possibly something internal in the battery when you dropped it. As Tam said first thing to do is change the atomizer.
  4. Like
    Squid got a reaction from Walt in Build advice   
    1st piece of advise using a mech mod, read, learn and understand Ohms Law so you don't become a statistic. That IMHO is the 1st step in using a mech.
  5. Like
    Squid got a reaction from joesmok99 in White thing inside Horizontech Falcon   
    Got a better pic? My only guess is a sheet of plastic mistakenly put there in the factory, if that's the case I'd remove it.
  6. Like
    Squid got a reaction from CoryTheNube in new here   
    Using e-cigarettes is vaping.....
  7. Like
    Squid got a reaction from Walt in Needing advice   
    The tpriv only will support down to.1 ohm. Your .15 ohm coil is very close to the limit, and due to production tolerances and other factors, the mod may be reading it as too low of a resistance or a shorted coil. I suggest a coil in the .25 ohm range. That should get you going.
  8. Like
    Squid got a reaction from Walt in glass doesn't stick to any part of the head   
    Did the orings fall out?
  9. Like
    Squid got a reaction from Bebop in Who's using a Pod system?   
    So the point of the salt nic is to deliver high nic without being harsh?
    If that's the case, then I need to stop thinking I need to try it. About 3 months ago I started cutting 3mg in half. Been trying to reduce my nic intake since March of 2011 when I started vaping.
  10. Like
    Squid got a reaction from Walt in Who's using a Pod system?   
    So the point of the salt nic is to deliver high nic without being harsh?
    If that's the case, then I need to stop thinking I need to try it. About 3 months ago I started cutting 3mg in half. Been trying to reduce my nic intake since March of 2011 when I started vaping.
  11. Like
    Squid got a reaction from Walt in tank getting warm while vape   
    The act of vaping is driven by heat. When you vape the cartomiser (your type of "tank") is going to get warm. How warm depends on the Ohms of the coil, the voltage of the battery, and how long and how often you drag on it. If you are chain vaping, it will get quite warm. My tank, a Melo3 gets quite warm on my way home from work while I take many long hits during the 40 minute ride home.
  12. Like
    Squid got a reaction from BOYAX777 in hi all im new to this..please help..   
    No, .1 is too low.
  13. Like
    Squid got a reaction from Walt in Happy Trails   
    Congrats. After almost 6 years of vapong, I have just cut my subohm tanks to 1.5mg, and my ohm-plus tanks to 4ishmg. Working toward that 0mg goal slowly.
  14. Like
    Squid got a reaction from Walt in Eleaf ikonn 220 with Ello Sub-Ohm tank   
    For setting up in wattage mode, it's pretty much the same for all mods.
    For coils under 1 ohm, I start around 10watts and slowly increase until I get a vape I like. You'll get a burnt taste if you go too high, back down half a watt or so and you have the sweet spot for that juice. As an example I run .5ohm coils around 25 watts. Sometimes a little higher sometimes a little lower, depending on the juice. Then there are a few juices I get on occasion that I will run as high as 45 watts.
    There is no magic setting that a specific mod will run at, just a ball park.
  15. Like
    Squid got a reaction from Nagual in Eleaf ikonn 220 with Ello Sub-Ohm tank   
    For setting up in wattage mode, it's pretty much the same for all mods.
    For coils under 1 ohm, I start around 10watts and slowly increase until I get a vape I like. You'll get a burnt taste if you go too high, back down half a watt or so and you have the sweet spot for that juice. As an example I run .5ohm coils around 25 watts. Sometimes a little higher sometimes a little lower, depending on the juice. Then there are a few juices I get on occasion that I will run as high as 45 watts.
    There is no magic setting that a specific mod will run at, just a ball park.
  16. Like
    Squid got a reaction from Walt in Winter Window Woes Blinded by the Light!   
    That's possible, I use paper towels.
  17. Like
    Squid got a reaction from Walt in Winter Window Woes Blinded by the Light!   
    I use ArmorAll window cleaner. Takes a bit of elbow grease and a couple doses at one time, but it works for me. Back window of my truck is tinted anyway, I don't bother with it.
  18. Thanks
    Squid got a reaction from Ternunda Hunter in "Wattage Mode" SMOK T-Priv   
    To my knowledge, all Smok coils are kanthal, so you should be running in wattage mode. As far as the blinking lights, I am no help, sorry.
  19. Like
    Squid got a reaction from Walt in Ohms law related question   
    My guess on the way they come up with the recommended range is a dart board........ I personally have very rarely if ever found the recommended range to work for me. For example, I run my baby beast with the .4ohm coil around 30-35 watts depending on the juice. 40 is too high for me.
  20. Like
    Squid got a reaction from leadpipe58 in Templar child proof cap won't come off   
    I wish I had an answer for you, but @christopher should be able to help out on this one. 
  21. Like
    Squid got a reaction from Tam in Why do i have to prime constantly?   
    Priming generally refers to setting up a fresh coil. Putting a few drops on the cotton of the coil before installing it in the tank, or letting a fresh coil sit for a time in a full tank of juice. A combination of the 2 methods can be used as well. Never heard of "priming a coil" repeatedly. Can you elaborate on the process you are using?
  22. Like
    Squid got a reaction from Tam in suggestion [Feature Request Approved]   
    Might I suggest changing the name of this section from "Feedback, Help & Requests" to "Site Feedback, Help & Requests"?  Seems that from time to time there is a bit of confusion and quite a few "Help it Broke" topics get posted here......
  23. Thanks
    Squid got a reaction from Bebop in ISTICK 50W   
    One of the 2 cells could be weak. LiPo cells act funny when they get old sometimes. I have a couple batteries for my RC cars that do that too. I took one apart and one cell was dead, the other was fine. No fix for it that I know of.
  24. Like
    Squid got a reaction from Tam in iStick Power Nano   
    My wife still loves the little unit, but  it seems to be aging fast.  The fire button has begun to not work intermittently, and the battery seems to be loosing it's staying power. She has to charge mid-day now so it does not die while watching TV before bed. It used to last all day. So what does a guy do???? Just got a new one in the mail from the VT Store today......
  25. Like
    Squid got a reaction from Walt in iStick Power Nano   
    My wife still loves the little unit, but  it seems to be aging fast.  The fire button has begun to not work intermittently, and the battery seems to be loosing it's staying power. She has to charge mid-day now so it does not die while watching TV before bed. It used to last all day. So what does a guy do???? Just got a new one in the mail from the VT Store today......

Vapor Talk Forum

Vapor Talk is a worldwide retailer of electronic cigarettes, e liquids, vape mods & more! Our Store and Online Vape Forum has served over 1 million+ Users since 2008.

Locations

Vapor Talk North America
41419 Pear Street, Murrieta, CA 92562
Phone: 1-888-315-VAPOR

Vapor Talk China
Locations: Beijing, Qingdao
Phone: +88-1-400-698-2209
×
×
  • Create New...