Christopher

Thank you @Christopher!!!  To me this is soooooo important!  Especially now that many atties are coming out under .1 ohms.  This is a great chart for regulated mods as well.  Not all regulated mods are created equal.  Not all specs on mods can be trusted.  Couple that with the insane specs published by battery manufacturers and you have a recipe for disaster.  Batteries are not simple power sources.  Some can generate impressive short term current but heat up fast.  I'm sure I am OCD in regard to this subject but along with the most important postulate, "Be Safe" there's also the consideration of press.  Whenever a battery goes into thermal runaway our community suffers from the negative press.  No need to give the anti's ammunition.  When some moron builds a .04Ω pipe bomb my prognosis of vaping for the rest of my life diminishes. 

I'd just get a new set and recycle those. No sense taking a chance on unknown/old batts.

Yep. Like @Squid said, I'd get new batteries too. Anytime I have any trouble at all with a battery, it's just safer to start with new.

This is actually a great question and one that I'm often asked. There is an easy way to actually visually see the difference between vaping and cigarettes. 
Grab a smoker and some tissue. Fold the tissue in half, then ask the smoker to blow through the tissue. Ask them to do this three more times. You'll be absolutely shocked at the yellowing left behind on the tissue paper. Now, repeat the process with your e cigarette, do it 5 or even 10 times. You should notice, no stain And if for some reason there was a stain, switch liquids because I've done this test more times than I can count for people and I've never stained tissue with an e-cigarette. 
On a side note, as british born guy, I'm pretty self conscious about my teeth. (Cavity free my whole life!). When I was a smoker, no matter how hard I tried, I generally suffered from yellowing. These days I'm pretty happy with how white my teeth are. It's been 8 years now and my teeth look great. (And any yellowing that I do  have is likely from coffee). 

Thank you, thank you, thank you!! You are the man@Christopher!!!

Sent using The Vapor Talk mobile app

Hey Gadget, 
Jeff broke it. Actually, we are having some issues with our open API that supports tapa talk and the Vapor Talk app. I hope to have this resolved as early as today. It's not you, it's us. 

It's here!
I special ordered a Therion DNA 166 from Vapor Talk (thanks Chris) and it is everything I expected. This thing a beautiful and it vapes like a dream!

Hey Gadget, 
Jeff broke it. Actually, we are having some issues with our open API that supports tapa talk and the Vapor Talk app. I hope to have this resolved as early as today. It's not you, it's us. 

This is actually a great question and one that I'm often asked. There is an easy way to actually visually see the difference between vaping and cigarettes. 
Grab a smoker and some tissue. Fold the tissue in half, then ask the smoker to blow through the tissue. Ask them to do this three more times. You'll be absolutely shocked at the yellowing left behind on the tissue paper. Now, repeat the process with your e cigarette, do it 5 or even 10 times. You should notice, no stain And if for some reason there was a stain, switch liquids because I've done this test more times than I can count for people and I've never stained tissue with an e-cigarette. 
On a side note, as british born guy, I'm pretty self conscious about my teeth. (Cavity free my whole life!). When I was a smoker, no matter how hard I tried, I generally suffered from yellowing. These days I'm pretty happy with how white my teeth are. It's been 8 years now and my teeth look great. (And any yellowing that I do  have is likely from coffee). 

This is actually a great question and one that I'm often asked. There is an easy way to actually visually see the difference between vaping and cigarettes. 
Grab a smoker and some tissue. Fold the tissue in half, then ask the smoker to blow through the tissue. Ask them to do this three more times. You'll be absolutely shocked at the yellowing left behind on the tissue paper. Now, repeat the process with your e cigarette, do it 5 or even 10 times. You should notice, no stain And if for some reason there was a stain, switch liquids because I've done this test more times than I can count for people and I've never stained tissue with an e-cigarette. 
On a side note, as british born guy, I'm pretty self conscious about my teeth. (Cavity free my whole life!). When I was a smoker, no matter how hard I tried, I generally suffered from yellowing. These days I'm pretty happy with how white my teeth are. It's been 8 years now and my teeth look great. (And any yellowing that I do  have is likely from coffee). 

If you are anything like me you will find that over time your collection of vaping stuff will seem to magically grow by leaps and bounds. Especially if you start to DIY your own juice. And your patience with sorting through jumbled mess in a shoe box will quickly wear thin. With this in mind I came up with a no frills design that anyone can make cheaply (under $10) and very quickly but will allow you to expand as needed.   Here Is what we are making. One for Juice bottles and One for Atomizers.       First step is deciding where you are going to place it. Whether in a cabinet, cubbie hole, a desk or table top then measure and write down height,width, and length. Now we drive to Home Depot for the 2 types of wood needed. I already had the materials at home left over from other projects so I just made both. You can do the same or just one or the other.   First the juice bottle one.   You need a 2"x2"x8 foot board (although they actually measure 1 1/2" wide not sure why?) Cost is around $2   Now you decide if you want Home Depot to cut your wood to size which they will they just won't guarantee precision cuts.   Based off of the measurements you took before, If your shelves are going to be less than 36" long then you need 3 of each size if more than 36" then you need 4 of each   2" 4" 6" 8" If more than 4 shelves high than go up on each piece by 2"   This will form your bases.   Next look for this cart somewhere in the lumber section.        Look at the 1 1/2" size pieces (poplar is the cheapest) and grab the amount for the number of shelves you plan to make in either the precut  sizes or have them cut down to the size needed by Home Depot.     For my 2 units I used (1) 2x2x8 and (4) 1/4x1 1/2x48  hobby boards. The bottle space was 34" long so I needed 3 bases up to 8" high and 4 shelf's 34" long. I used (3) of the remaining 14" hobby boards on the atomizer shelf and cut (2) 6" high bases leaving me with a 10" piece of 2x2x8.   Once back home find a flat place to work and grab any type of glue and start assembling the bases. Starting with the largest 2x2 piece lay it on it's side add glue to one side of next smaller size and stack it on top like so.   While glue is still wet adjust the pieces so cut edge and sides line up as even as possible. Continue on until all bases are glued. Allow glue to dry for a few minutes.   Place bases with cut edge down where you planned for with 3rd one in the middle or 3rd & 4th evenly spaced for longer shelf's. Then place hobby boards on other cut edge like so         For the atomizer one there is an extra step. Grab a pencil, ruler, and some atomizers. Lay them like so.   This will help you get a feel for how many will fit on your shelf and what spacing is needed between them. Then make 3/4 of an inch mark on both edges of shelf and using another shelf as straight edge draw a line down the center. Now transfer your spacing marks to that line.   Now grab a drill and a bit that is slightly larger than your 510 connector on the bottom of the Atomizer (I used 9/32) and drill at your marks you can either drill all the way through or stop right before test with an atomizer to make sure base lays flat against shelf.   Do the same for other shelves.   Once you are done with that I recommend you glue shelves to bases.   And were done! As I said at first no frills but very useful.   Now you get to decide what else you could use this shelf for or maybe sand and stain or paint them. After finding more attys (I swear they are reproducing by themselves) I added a couple of more shelves And here is one way that I decided to finish it.         As for me after looking at the first picture I really need to get my bottle labels under control and now I know exactly where to place them on the bottle for optimum viewing.   Thanks for reading. As always all comments, critiques, and or questions are much appreciated.

Ah yes!  You eeeee-ville Vaper you!  Actually sounds like a good title to a movie.  Kinda B stock but it could be a hoot.

hi guys my name is Gabi I am new here nice to meet you all :D

That's not unusual. Drama always fuels conversation. It's probably why Vapor Talk, at least compared to many other forums, is usually a little "quieter." Over the years, we always quickly shut down those types of posts. Debate of course is always fine but the rule is always "attack the topic and not the poster."  

I had to share this as I find it so awesome. Google's voice technology varies it's output depending on the accent that is used. 
 

I had to share this as I find it so awesome. Google's voice technology varies it's output depending on the accent that is used. 
 

That's not unusual. Drama always fuels conversation. It's probably why Vapor Talk, at least compared to many other forums, is usually a little "quieter." Over the years, we always quickly shut down those types of posts. Debate of course is always fine but the rule is always "attack the topic and not the poster."  

Thank You :D 
Actually we are going to start auto posting "interesting" topics to Facebook and Twitter as a way to drum up more conversation within the forum. We have a ton of followers that hang out more on social media that on the forum so this helps draw them back into the forum. 

Hey Tam
Multiple ohm versions are coming down the pipeline (if not already done). I sent Roger an email last night confirming when we'll get more and also what options we have (I believe 1.6ohm). 

Hi Folks, 
We're happy to announce that Vapor Talk Branded products now ship free of charge, no minimum. Your cart must contain only Vapor Talk Branded products in order to qualify for the free shipping option. (U.S. Residents Only)
Thanks,

Hi Folks, 
We're happy to announce that Vapor Talk Branded products now ship free of charge, no minimum. Your cart must contain only Vapor Talk Branded products in order to qualify for the free shipping option. (U.S. Residents Only)
Thanks,

Thank You :D 
Actually we are going to start auto posting "interesting" topics to Facebook and Twitter as a way to drum up more conversation within the forum. We have a ton of followers that hang out more on social media that on the forum so this helps draw them back into the forum. 

That's not unusual. Drama always fuels conversation. It's probably why Vapor Talk, at least compared to many other forums, is usually a little "quieter." Over the years, we always quickly shut down those types of posts. Debate of course is always fine but the rule is always "attack the topic and not the poster."  

Thank You :D 
Actually we are going to start auto posting "interesting" topics to Facebook and Twitter as a way to drum up more conversation within the forum. We have a ton of followers that hang out more on social media that on the forum so this helps draw them back into the forum. 

This is a great live session between the Vaping Biker and Mouch.  Fabulous information!!!!!