Tam Posted November 15, 2012 Share Posted November 15, 2012 Okay, so I've been direct dripping for a little while now. So far I've had wonderful luck with all the various atomizers I've used. Just recently I opened up a new Boge 2.0 ohm atty and... the vapor was extremely harsh. The thing popped several times and makes a strange little almost gurgling noise when I draw from it. None of the other atomizers in that pack had this happen. Does this mean it's a bad one? What are your experiences with bad atomizers and what are some of the "symptoms" of one? Any information you can give is greatly appreciated. Link to comment Share on other sites More sharing options...
Jeffb Posted November 15, 2012 Share Posted November 15, 2012 Sounds like it may be running hot. I bet if you checked it the ohm rating is lower than 2ohms. Do you have a device that you can turn down the voltage? Link to comment Share on other sites More sharing options...
Tam Posted November 15, 2012 Author Share Posted November 15, 2012 I have an eGo twist and a Vision Spinner that I tried it on at all the different settings. It still gives off a very harsh vapor that gives me a sore throat. Link to comment Share on other sites More sharing options...
Rixter Posted November 15, 2012 Share Posted November 15, 2012 Since you've been dripping for a little while, I figure that you know what you're doing now. If your atty isn't performing like your others have in the past, I'd guess that it's probably a defect and just chalk it up to a bad coil wrap or something funky with the wick. Sputtering and/or poor vapor production are usually signs that you have gotten hold of a bad one (duh), but sometimes you can blow them out (from the threaded end), blot the inside with a tissue, and drip a few drops in to get it going. I've had some strangely performing atties come my way in the past, and if said atty continues to act "contrary" (as we say in the Deep South) and all else fails, I just toss it and grab a new one. BTW, have you received your 901s yet? Link to comment Share on other sites More sharing options...
Jeffb Posted November 15, 2012 Share Posted November 15, 2012 If it was mine I would toss it Link to comment Share on other sites More sharing options...
Tam Posted November 15, 2012 Author Share Posted November 15, 2012 Since you've been dripping for a little while, I figure that you know what you're doing now. BTW, have you received your 901s yet? Doesn't matter how long I've been doing whatever, Rixter, I still don't know what I'm doing on any given day. Yes, I've gotten the 901s and have used them. They're a bit different from the 510s I've been using. I'm still not sure what I think of them but they've been pretty good so far! Thanks for the rec. They're nice to switch off to... Link to comment Share on other sites More sharing options...
Tam Posted November 15, 2012 Author Share Posted November 15, 2012 If it was mine I would toss it That thought crossed my mind but I wanted to check first to make sure. Thanks for the info and the advice! Link to comment Share on other sites More sharing options...
Tam Posted November 15, 2012 Author Share Posted November 15, 2012 BTW, have you received your 901s yet? Ha! I just hadn't found the right combination yet until I tried it again tonight. A 3.5 ohm 901 at 4.0 on a Twist with Sweet-Vapes' 12 mg, 70/30 PG/VG mix of Pineapple Upside Down Cake... OMG. *dies* I think I just found heaven! Link to comment Share on other sites More sharing options...
lindsayfox Posted November 15, 2012 Share Posted November 15, 2012 Hot liquid and high voltage can make gurgling sound and harsh taste,Try to mnimise the voltage as it would certainly one reason for this issues. Link to comment Share on other sites More sharing options...
Tam Posted November 15, 2012 Author Share Posted November 15, 2012 Thanks, Lindsay. I did try it on all the different settings on both the twist and the spinner with the same effect so I guess we'll just chalk this one up as a dud and chuck the thing. Link to comment Share on other sites More sharing options...
Viper Ron Posted November 15, 2012 Share Posted November 15, 2012 The QC in China, let me tell ya..........Wait! There is no QC.....lol Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now